Contractor Quotes BG

How to Increase the Water Pressure in your House

How to Increase the Water Pressure in your House
The steps on how to increase the water pressure in your house might seem like a daunting task. But you should know that the best way to address this is by determining the reason behind the low water pressure. There are lots of causes of low water pressure. Surprisingly, most of them will only require simple remedies and can even be done without the need to hire professional plumbers.

Unfortunately, a lot of people thought that addressing the problems of low water pressure takes a lot of effort, money and time. This is why they just simply live with poor water pressure. But no one certainly wants to go home after a long day at work and not being able to enjoy a refreshing shower just because of poor water pressure. So if you are having poor water pressure issues in your home right now, here are some of the most effective ways on how to increase the water pressure.

Increasing Pressure at One Faucet

The first step is to work on one faucet. Begin by cleaning the aerator and then unscrewing it right at the end of the faucet with the use of pliers. After which, you need to disassemble the aerator while taking note of how they will fit together. Rinse off the dirt and the sediment and then let the faucet run for a couple of minutes in order to dislodge the presence of sediments in the pipe.

If the aerator still appears to be dirty, soak them with an equal mix of water and white vinegar for at least three hours. In order to avoid any scratches, wrap the cloth on the aerator right before you take it off. You can then clean the showerheads in the same manner.

The next thing to do is to check the faucet if it still is having low pressure issues. If it is, then it has to be disassembled. To do this, unscrew the stem retainer nut and then pull slowly the stem going up. You might need to take off the retaining collar.  When it comes to dealing with a tub faucet that is single handed, you will come across a screw on each side of the tub right below the large chrome piece. Make sure that both of these are tightened fully right before the step is removed.

The next step is to repair the faucet and to check if there are any problems based on what you will see. First off, if you notice that the water or spring at the base of the stem, take them off with the use of a screw driver. Rinse the sediments off or perhaps, replace them if necessary. If you notice a more complex mechanism, then get help from the experts.

Right after you do repairs on anything that seems amiss, what you can do next is to reassemble the faucet. With the use of a cup, block the faucet and turn on and off the water for a few times. Doing this will flush anything that causes the clog which might be the reason behind the poor water pressure.

Fixing a Recent Poor Water Pressure Problem

To fix a recent issue with poor water pressure, you should start by addressing any problems related to hot water supply. If it is only your hot water tap that has low pressure, then check any problems on your water heater. Another reason is the sediment that is clogging right at the water supply and water heater line. Flush off the tank but if this will not work then you will need to call a plumber. In order to prevent this from happening again, you must replace the anode rod in a regular basis and then install water softener.

Remember, you have to keep in mind that pipes for hot water supply are often very small. A lot of times, the pipe that leads from your water heater usually have at least 3/4 inch in diameter so this could be another reason. Moreover, the leaks on the valves and the tank itself are also another culprit. However, you should only attempt to repair these if the leak is just small and that you have some knowledge about plumbing work.

Another thing to do is to check if there are any pipes leaking. Leaks are pretty common and these are often the cause of low water pressure. So conduct a quick check for any damp spots right beneath the pipes, most especially on the main power line. The moment you encounter any pipes leaking, make sure you immediately fix it. The supply line usually enters the house on the side during mild climates or from the basement floor during cold climates. The small damp spots might be due to the condensation. To address these, simply place a couple of paper towel and then check on the following day to inspect.

The next thing to do is to test your toilet for any leakage. A toilet mechanism that is leaking will fail to block the flow off the tank towards the bowl. Simply put some drops of food coloring at the tank then go back in an hour or two without having to flush the toilet. If the food coloring has gotten into the bowl, then your toilet must be repaired. Generally, all it will require is a new flapper and some cheap easy fix.

Addressing History of Low Water Pressure

You must also check the history of the problem. Begin by replacing old supply pipes. Trace the main supply line that you should find on the side portion of your house or at the basement if you live in areas with cold weather. If for instance your supply pipe is magnetic or silver and comes with threaded fittings, then they are probably made of galvanized steel. The old galvanized pipes usually clog due to mineral buildup or at the event of corrosion which slows down the flow of water. Replacing the pipes with those made of plastic or copper can best resolve this problem.

Another way to best address your problem on low water pressure is to check the supply pressure yourself. Look for a pressure gauge that can attach to a hose bib. You should easily find this at any hardware store. Make sure that no one in your home is using the water supply when you are doing this. Slowly hook the gauge into the hose bib and you should be able to read the pressure.

If the pressure is lower than what the water service is claiming then there is an issue on the water main. In this case, you should talk to your water service provider or perhaps, in your local water municipality to check if you can have them to repair the main. You can also ask them for help. If you cannot get the service to repair, then install water pressure booster.